Can I use regular LED lights to plant plants indoors?

Nov 11, 2025

Leave a message

一, Basics of photobiology: What plants need and how to match their spectra
Chlorophyll is what plants use to absorb certain wavelengths of light. The main bands are red light (600–700nm) and blue light (400–500nm). Red light controls the production of flowering hormones by using photosensitive pigments. This helps fruits store more sugar. Blue light, on the other hand, stops stems from growing longer and speeds up the production of chlorophyll by using cryptochrome. Experiments reveal that when the ratio of red to blue light is 4:1, the amount of dry matter in lettuce increases by 30% compared to when it is only one colour, and the amount of chlorophyll increases by 22%.


But the way that normal LED lights are made is based on what is comfortable for people to see, and they usually have a lot of green light (500–600nm) that doesn't help plants. For instance, a white LED creates a whole spectrum by exciting yellow fluorescent powder with a blue light chip. However, the amount of red light is less than 20%, which is far less than the 40% to 60% needed for plants to thrive. This spectral imbalance makes plants less efficient at photosynthesis, and using it for a long time might produce problems including yellowing leaves and weak root systems.

二, Differences in technology: A basic comparison of regular LED lights and plant growth lights
1. The ability to change the spectrum
Professional plant growth lamps get fine spectrum control by using multiple chips together:

Red blue light combination: During the nutritional growth period, a 3:1 ratio is employed to help leaves expand, and during the reproductive growth period, far red light (730nm) is raised to 15% to start blooming.
Design for the full spectrum: Simulate the solar band (400–720 nm), get rid of ultraviolet and infrared rays, and lower the chance of heat damage.
The spectrum of regular LED lights, on the other hand, is set and can't be changed based on the growth cycle of the plants. For instance, the red peak of 5000K white LED lights that are often used in homes is only 620nm, and the amount of blue light is too high (approximately 35%). This could cause leafy vegetables like lettuce to grow too much.

2. Managing heat and using energy wisely
LED technology has several benefits, such as low heat output and great luminous efficiency (around 200lm/W). However, there are differences in how typical LED lights and plant growth lights get rid of heat:

Plant growth lamp: uses a ceramic heat dissipation substrate or an active liquid cooling system to keep the chip temperature below 60 °C, which extends its life to 50,000 hours;
Regular LED lights employ aluminium heat sinks, and if you use them for a long time at a high intensity, the chip temperature can go over 80 °C, which speeds up light decay.
In a vertical farm test in Shenzhen, the professional plant growth lamp board was 15 °C cooler than regular LED lamps after 12 hours of continuous use. The plants' transpiration rate also went up by 18%.

3. Brightness and evenness of the light
Plants need to grow in a way that meets the criteria of photosynthetic photon flux density (PPFD):

For leafy vegetables, the range is 200–400 μ mol/m ²/s. For flowering and fruiting plants, the range is 400–800 μ mol/m ²/s.
Because they have a set emission angle (typically 120 °), regular LED lights need to be used in different combinations to cover the planting area. For instance, to get 200 μ mol/m ²/s in a planting area of 1 square meter, you would need to install 4 regular 10W LED lights. On the other hand, a single 60W professional plant growth light can cover 400 μ mol/m ²/s evenly.

三, Real-world application results: data from experiments and case studies
1. Experiment with extra light for a short time
In a 30-day comparative experiment conducted on a north-facing balcony (light intensity < 5000 lux):

The ordinary LED light group uses three 10W white LED lights to add light for eight hours a day. The number of lettuce leaves goes up by 12%, but the stem diameter is 0.3mm narrower than the natural light group.
Plant growth lamp group: The number of lettuce leaves grew by 28%, the stem diameter grew by 0.5mm, and the VC content grew by 15% when using one 60W red blue light plant lamp.
2. Examples of planting over a long period of time
A person in Shanghai used regular LED lights to cultivate tomatoes. After six months, these problems happened:

Delayed blossoming time: flowers came out 12 days later than the group with natural light;
Fruit deformity: 30% of fruits show cracks;
Cost of energy use: The monthly electricity bill is 40% more than that of the group with the plant growth lamp.
After converting to professional plant growth lamps, tomato yield went up by 25%, the amount of soluble sugar in the fruit went up by 18%, and energy use went down by 30%.

四, Industry Solution: Strategy for Improving Regular LED Lights
1. Plan for spectral supplements
People who don't have a lot of money can utilise "ordinary LED lights+red and blue light supplement boards" together:

Basic lighting: Use a 5000K white LED light to brighten your space every day;
Adding a 660nm red LED module during the blooming phase and giving the plants an extra 4 hours of light per day can speed up the flowering process by 15%.
2. Control of a changing light environment
Using smart sockets to set up time-sharing lighting:

Nutritional growth period: From 6:00 to 18:00, turn on the white LED. From 18:00 to 22:00, switch to the blue LED.
During the reproductive growth stage, turn up the far red LED from 22:00 to 2:00 to help plants' circadian rhythm.
3. A system that works together with multiple spectra
It can be utilised alongside other things in small planting boxes.

Top lighting: a 40W full-spectrum LED light board (PPFD 300 μ mol/m ²/s); side lighting: a 10W red LED strip (660nm) to make the fruit colour more vibrant.
This method boosted strawberry yield by 40% compared to a single white LED and improved fruit sugar content by 2 ° Brix in the home balcony test.
 

Send Inquiry